Vector V08 Manual do Utilizador Página 38
- Página / 60
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
INSTALLATION DIRECTIVE MAY 2006
38
V08 ENT M75
-
M11
-
M12
16. FIRST ENGINE START
Before starting the engine, please make sure the sea water
gate valve is open, check the levels of the lubricating oil and
of the engine coolant, and complete venting the air from the
fuel feed loop, acting on the hand pump of the prefilter or
with the aid of a dedicated electrical pump. Loosen the vent
fitting on the prefilter and operate the pump until only fuel
without air flows out.
Venting fuel supply line
1. Prefilter vent fitting - 2. Vent fitting on the filter support -
3. Vent fitting on the high pressure pump.
o Loose the vent fitting on the prefilter (1) and operate
the pump until only fuel without air flows out. Tighten
the vent fitting.
o Loosen the vent fitting (2) on the filter support and
operate the pump until only fuel without air flows out.
o Tighten the vent fitting (2) and continue pumping during
the initial start-up phases.
Make sure that the fuel that flows out of the fitting is not
dispersed in the environment.
Only if the engine starting is very difficult, stop the engine,
insert a hose on the vent fitting of the high pressure pump
(3), loose the junction and start the engine for a few seconds.
Stop the engine, remove the hose and tight the junction to
the prescribed torque value. Make sure that the fuel that
flows out of the fitting is not dispersed in the environment.
Start the engine.
CAUTION
Never attempt to vent the high pressure system as this is
useless and extremely dangerous.
CAUTION
Avoid accurately that fuel comes into contact with the
alternator belt.
Start-up procedures
1. Control selector from bridge or engine room -
2. Power supply switch of the engine electric circuits -
3. Start button from engine room -
4. Button for managing acceleration and deceleration.
The electrical equipment of this engine allows starting it
from the “engine room” and from the “bridge”.
NOTE
A few moments after start-up, make sure sea water is cor-
rectly drained from the relevant circuit.
Starting the engine from the bridge
This is allowed only if the Relay box switch (1) is in the
“BRIDGE” position.
Procedures and warnings are provided in the operation and
maintenance manual.
Starting engine from the “bridge”
- Switch over the switch (1) of the relay box in the posi-
tion “ENGINE ROOM”.
This operation excludes all the bridge controls and must be
absolutely avoided when the engine has been started.
- Switch over the switch IGNITION (2) to power the
electric circuits of the system and enable the controls
available on the panel.
- Press the button START (3) to start the engine.
WARNING
The engine start is fully controlled by the ECU; the start-up
phase begins when the button START is released.
Engine shut-off from “bridge”
The engine shut-off occurs switching over the switch IGNI-
TION (2).
Bringing again the switch (1) in position “BRIDGE”, the use of
the controls will be disabled on the Box, enabling the start-
up only the bridge controls.
Figure 44
Figure 43
05_016_V
1
2
3
"2)$'%
2//-
)'.)4)/. 34!24 20-
20-
%.').%
#(%#+
1 32 4
05_007_V
- V08 ENT M75 1
- V08 ENT M11 1
- V08 ENT M12 1
- INSTALLATION DIRECTIVE 1
- FOREWORD 2
- CONTENTS 3
- Figure 1A 6
- Figure 1B 7
- Figure 2A 8
- Figure 2B 9
- 3. INSTALLATION OVERVIEW 10
- Open sea water cooling line 12
- Dimensions 13
- Gear box oil heat exchanger 13
- Power takeoffs (optional) 13
- 6. IDENTIFICATION DATA 14
- 7. FUEL LINE 15
- Prefilter 15
- Materials Characteristics 15
- Fuel supply system scheme 16
- Hydraulic connections 16
- 8. ELECTRICAL EQUIPMENT 17
- GEAR BOX 18
- V08 ENT M 18
- Wire harness 19
- )'3" 20
- Electrical starting motor 21
- Alternator 21
- Battery recharging 22
- Relay Box 23
- (ECU) ADEM III 24
- Neutral gear sensor 25
- 04_233_N 26
- 04_250_N 27
- 06_131_V 27
- 04_234_N 28
- Maintenance 29
- Installation 30
- Checking indications 30
- Figure 30 31
- Figure 31 31
- OF THE MODULE 32
- SIDE WIRING 32
- Functions of the JD terminals 33
- Coolant temperature sensor 34
- Low level coolant sensor 34
- Oil pressure sensor 34
- Clogged air filter sensor 35
- Clogged oil filter sensor 35
- Clogged fuel filter sensor 35
- Engine shut-off from “bridge” 38
- RPM control 39
- 17. EDC ECU INDICATION LIGHTS 40
- CHECK Indication light 40
- WARNING Indication light 41
- SHUTDOWN (preliminary) 41
- Component Anomaly Code 42
- Wiring diagram key 46
- 20. ELECTRIC DIAGRAMS 46
- Connectors 48
- Indicator lights 48
- EDC connector J1 49
- EDC connector J2 50
- Sk Quadro princ V08pi 51
- MAIN PANEL SECONDARY PANEL 54
- Single engine 55
- Two-engines 55
- 21. APPENDIX 57
- 04_037_C 58
- 04_036_C 58
Zebra 105936G-003 manuales
Manuales del propietario y guías del usuario para Cabezales de impresion Zebra 105936G-003.
Ofrecemos 1 manuales en pdf Zebra 105936G-003 para descargar gratis por tipos de documentos: Ficha de datos
Comentários a estes Manuais