Vector SIMOVERT MASTERDRIVES 6SE70 VC Instruções de Operação Página 115
- Página / 162
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Vector Control Chassis Type Frequency Converter First Start-up
SIEMENS AG 476 869 4070 76 J AB-74
SIMOVERT MASTERDRIVES Operating Instructions 10-1
10 First Start-up
Unpack and check
the units
First start-up of a unit comprises the following work steps:
After removing the packaging, check that the unit
is intact and undamaged. Only intact units may be
started-up. Please also check that the unit is com-
plete, that the correct optional boards are fitted and
that the technology option has been released, if
ordered.
Mount the unit
and install optional
boards which have
not yet been fitted
Retrofit any optional boards which have not
yet been installed, if necessary. Then install the
units taking into account the requirements at the
point of installation and the EMC instructions.
Form the DC link
capacitors, if
necessary
If the DC link of the unit was de-energized for
more than one year, you have to newly form
the DC link capacitors.
Connect the pro-
tective conductor, the
power cables or the
DC link buses and, if
present, the external
24 V incoming supply
Starting with the protective conductor, please connect
the power cables or the DC link buses and, if
present, the external 24 V supply. When laying the
cables, please observe the EMC instructions. During
this work step, please do not yet connect control
cables, communication cables, encoder cables
and motor cables (exception: cables for connecting
up an OP1S, if parameterization is intended to be
carried out via the OP1S).
Power up the external
24 V supply or
the line voltage
After checking that the cabling has been correctly
connected and that it sits properly, power up
the external 24 V supply or the line voltage. After
the electronic power supply is started, the unit
initializes itself. This action can take several seconds.
The drive status is subsequently shown on the PMU.
If necessary, carry
out parameter reset to
factory setting
If the PMU does not show status °005 after com-
pletion of the unit initialization, or if the unit has
already been parameterized before, you shoud
carry out a parameter reset to factory setting.
See
"Transport,
Storage,
Unpacking"
See
"Installation"
and
"Installation in
Conformance
with EMC
Regulations"
See
"Forming"
See
"Connecting-up"
and "Installation
in Conformance
with EMC
Regulations"
See
"Parameterization"
- SIMOVERT MASTERDRIVES 1
- Vector Control 1
- Contents 3
- 1 Definitions and Warnings 5
- 2 Description 9
- 4 Technical Data 13
- Fig. 4-1 Derating curves 14
- EB1: Expansion Board 1 24
- EB2: Expansion Board 2 24
- Significance of the 24
- 4.2 Installation notes 27
- 4.4 Venting the heat sinks 30
- 5 Installation 31
- Fans, volumetric 36
- Regulations 41
- 7 Connecting-up 43
- 7.1 Power connections 46
- Fig. 7-4 View of the CUVC 50
- 8 Parameterization 55
- Components Order Number 59
- OP1S 6SE7090-0XX84-2FK0 59
- Fig. 8-2 View of the OP1S 60
- Selection of factory setting 62
- Start of factory setting 62
- 9 Parameterizing steps 65
- P070 Order No. 6SE70 67
- P072 Rtd Drive Amps 67
- P073 Rtd Drive Power 67
- P366 Select FactSet 67
- Automation unit 71
- (e. g. SIMATIC S7) 71
- USS via RS232 71
- P060 Menu selection 72
- P072 Rtd Drive Amps(n) 72
- P073 Rtd Drive Power(n) 72
- P109 Pole pair number 73
- P700.01 = ? 76
- P740 = ? 76
- P918.01 = ? 76
- 87654321 81
- Setpoint source 81
- MASTERDRIVES VCUSS1 (P368=4) 85
- MASTERDRIVES VC 88
- V/f characteristic (P100=1) 89
- V/f characteristic (P100=2) 90
- MASTERDRIVES VCTextile 90
- P354 is referred to P113 * ) 94
- 9.3 Detailed parameterization 96
- 3AC 380 V to 480 V 97
- 3AC 500 V to 600 V 97
- 3AC 660 V to 690 V 97
- 9.3.2 Board configuration 98
- 9.3.3 Drive setting 101
- P095 = 10,12,13 P095=11 103
- 10,13,14 104
- 11,12,15,16 104
- P384.02 = ? 106
- P384.02 = 0 106
- 10 First Start-up 115
- 11 Faults and Alarms 117
- ≠ 0 and thus a valve must be 129
- ≠ 0 and therefore a valve 130
- Check P690 SCI AnaIn Conf 136
- Table 11-3 Fatal errors 139
- 12 Maintenance 141
- 12.1 Replacing the fan 142
- (from type G) 146
- 12.13 Replacing the IVI 148
- 12.15 Replacing the PSU 149
- 12.16 Replacing the IGD 150
- 12.20 Replacing the PMU 153
- Snap catches 153
- Adapter section 153
- 13 Forming 155
- Off-circuit idle 156
- Forming time 156
- 15 Certificates 159
- Test certificate 160
- Copyright ( 161
Manuais e produtos relacionados com Componentes para chassis Vector SIMOVERT MASTERDRIVES 6SE70 VC
(13 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais